This post below pertaining to Tools You Need to Install a New Bathtub is rather compelling. Read it for yourself and see what you think about it.
Installing a tub isn't specifically brain surgery, but it does require strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a moderately difficult job. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open up a wall surface to remove the old tub as well as place the brand-new bathtub, the job is a lot harder. In either situation, the task is within a house handyman's skills, although you will require an assistant to move out the old tub as well as set in the brand-new one. See to it you have actually certified yourself for the job and are comfortable trying it. As opposed to working with a professional to take over a halfway-completed job, it is far better to consider employing one before you begin. Possibilities are you may need an expert plumber to make tube connections.
This short article will assist you set up a new tub in your restroom if you have already purchased a brand-new bathtub and also do not require to alter the plan of your previous water system pipelines.
Your tools as well as material checklist need to consist of the following:
Getting ready for the Setup
First of all, the supporting structure provided with the bath ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the tap features a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to prevent pressure on the tub.
Fit the flexible faucet adapters to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, activate the taps to drain pipes any water staying in the system. The process of eliminating the existing faucets can be rather bothersome because of the limited access that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from transforming throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Using the two wooden boards under its feet, put the bath tub in the required position. The wooden boards are practical in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bath tub until the level reviews degree.
To install taps, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the other tap.
Turn on the supply of water as well as inspect all joints and also brand-new pipework for leaks as well as tighten them if needed. Load the tub as well as additionally examine the overflow electrical outlet and also the typical outlet for leaks.
Finally, repair the bath paneling as described in the producer's instruction manual. Tiling and also securing around the bath tub needs to wait up until the tub has been utilized a minimum of once as this will settle it right into its last placement.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin making sure that the washing machines are in area between the tap and also the sink. Safeguard the tap in place with the manufacturer supplied backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the tap finishes initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is required to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to break a rigid seal, creating the water to penetrate the wall surface between the bathroom as well as the tiling, leading to difficulties with dampness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealers to blend in your components as well as installations. They are offered in tubes and cartridges, and can sealing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Remember to constantly fill up the bath tub with water prior to sealing, to enable the activity experienced when the tub is in usage. The sealer can crack relatively very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily available on the market. It is suggested to fit the tiles using water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am very fascinated by How to Install a Bathtub and I'm hoping you enjoyed the new post. Do you know anybody else who is curious about A Step-by-Step Guide to Installing a Bathtub? Please feel free to promote it. Thanks a bunch for your time. Visit us again soon.
Book-Now